when blocks overlap then simulation error

Forum for DesignBuilder EnergyPlus simulation users to exchange views and questions. Posts regarding use of Detailed HVAC should go to the EnergyPlus HVAC forum

Moderator: DesignBuilder Support

mimarimsix
Posts: 1

when blocks overlap then simulation error

Postby mimarimsix » Wed Apr 10, 2019 10:24 am

Hi,
I'm analyzing a three floor building in Designbuilder. I created 3 separate blocks.
When I overlap the blocks, I will take simulation error. I write down the error. Please help me.





Program Version,EnergyPlus, Version 8.9.0-40101eaafd, YMD=2019.04.10 12:23,
** Warning ** Timestep: Requested number (2) is less than the suggested minimum of 4.
** ~~~ ** Please see entry for Timestep in Input/Output Reference for discussion of considerations.
** Warning ** ProcessScheduleInput: DecodeHHMMField, Invalid "until" field value is not a multiple of the minutes for each timestep: UNTIL: 17:55
** ~~~ ** Other errors may result. Occurred in Day Schedule=20002_dy_1
************* Beginning Zone Sizing Calculations
** Warning ** Weather file location will be used rather than entered (IDF) Location object.
** ~~~ ** ..Location object=MEHMET USDUN EVI (22-12:28-12) (22-12:28-12)
** ~~~ ** ..Weather File Location=ANKARA - TUR IWEC Data WMO#=171280
** ~~~ ** ..due to location differences, Latitude difference=[4.00E-002] degrees, Longitude difference=[1.06] degrees.
** ~~~ ** ..Time Zone difference=[11.0] hour(s), Elevation difference=[39.15] percent, [267.00] meters.
** Warning ** WindowProperty:FrameAndDivider: In FrameAndDivider 2 Inside Sill Depth is less than Inside Reveal Depth; it will be set to Inside Reveal Depth.
** Warning ** GetSurfaceData: Construction D2 DUVAR of interzone surface ZEMINKAT:ZX02ODA_PARTITION_2_0_0 does not have the same materials in the reverse order as the construction D2 DUVAR_REV of adjacent surface ZEMINKAT:ZX01GIRISHOLU_PARTITION_7_0_10003
** ~~~ ** ...but Nominal U values are similar, diff=[0.0000] ... simulation proceeds.
** ~~~ ** ...if the two zones are expected to have significantly different temperatures, the proper "reverse" construction should be created.
** ~~~ ** ...this problem for this pair will not be reported again.
** Warning ** GetSurfaceData: Construction AHSAP DOSEME_REVERSED of interzone surface ZEMINKAT:ZX02ODA_CEILING_1_0_0 does not have the same materials in the reverse order as the construction AHSAP DOSEME_REVERSED_REV of adjacent surface BIRINCIKAT:1X02SOFA_FLOOR_0_0_10000
** ~~~ ** ...but Nominal U values are similar, diff=[0.0000] ... simulation proceeds.
** ~~~ ** ...this problem for this pair will not be reported again.
** Warning ** GetSurfaceData: Construction D3 DUVARI of interzone surface ZEMINKAT:ZX07HOL_PARTITION_3_0_0 does not have the same materials in the reverse order as the construction D3 DUVARI_REV of adjacent surface ZEMINKAT:ZX06DEPO_PARTITION_5_0_10017
** ~~~ ** ...but Nominal U values are similar, diff=[0.0000] ... simulation proceeds.
** ~~~ ** ...this problem for this pair will not be reported again.
** Warning ** GetSurfaceData: Construction D1 DUVARI of interzone surface ZEMINKAT:ZX03ODA_PARTITION_4_0_0 does not have the same materials in the reverse order as the construction D1 DUVARI_REV of adjacent surface ZEMINKAT:ZX04ODA_PARTITION_6_0_10031
** ~~~ ** ...but Nominal U values are similar, diff=[0.0000] ... simulation proceeds.
** ~~~ ** ...this problem for this pair will not be reported again.
** Warning ** GetSurfaceData: Construction PROJECT PARTITION of interzone surface BIRINCIKAT:1X04MUTFAK_PARTITION_2_0_0 does not have the same materials in the reverse order as the construction PROJECT PARTITION_REV of adjacent surface BIRINCIKAT:1X05BANYO_PARTITION_5_0_10038
** ~~~ ** ...but Nominal U values are similar, diff=[0.0000] ... simulation proceeds.
** ~~~ ** ...this problem for this pair will not be reported again.
** Warning ** GetSurfaceData: Entered Zone Floor Areas differ from calculated Zone Floor Area(s).
** ~~~ ** ...use Output:Diagnostics,DisplayExtraWarnings; to show more details on individual zones.
************* Note that the following warning(s) may/will occur if you have not enclosed your zone completely.
** Warning ** Entered Zone Volumes differ from calculated zone volume(s).
** ~~~ ** ...use Output:Diagnostics,DisplayExtraWarnings; to show more details on individual zones.
** Warning ** CalculateZoneVolume: 6 zones are not fully enclosed. For more details use: Output:Diagnostics,DisplayExtrawarnings;
** Warning ** CheckUsedConstructions: There are 6 nominally unused constructions in input.
** ~~~ ** For explicit details on each unused construction, use Output:Diagnostics,DisplayExtraWarnings;
** Severe ** CalcHeatBalanceInsideSurf: The temperature of 636823.92 C for zone="BIRINCIKAT:1X03ODA", for surface="BIRINCIKAT:1X03ODA_EXTFLOOR_0_0_0"
** ~~~ ** ..is very far out of bounds during warmup. This may be an indication of a malformed zone.
** ~~~ ** During Warmup & Sizing, Environment=SUMMER DESIGN DAY IN MEHMET USDUN EVI (22-12:28-12) JUL, at Simulation time=07/15 00:00 - 00:00
** Fatal ** Program terminates due to preceding condition.
...Summary of Errors that led to program termination:
..... Reference severe error count=1
..... Last severe error=CalcHeatBalanceInsideSurf: The temperature of 636823.92 C for zone="BIRINCIKAT:1X03ODA", for surface="BIRINCIKAT:1X03ODA_EXTFLOOR_0_0_0"
************* Warning: Node connection errors not checked - most system input has not been read (see previous warning).
************* Fatal error -- final processing. Program exited before simulations began. See previous error messages.
*************
************* ===== Final Error Summary =====
************* The following error categories occurred. Consider correcting or noting.
************* Nominally Unused Constructions
************* ..The nominally unused constructions warning is provided to alert you to potential conditions that can cause
************* ..extra time during simulation. Each construction is calculated by the algorithm indicated in the HeatBalanceAlgorithm
************* ..object. You may remove the constructions indicated (when you use the DisplayExtraWarnings option).
*************
************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 0 Severe Errors.
************* EnergyPlus Sizing Error Summary. During Sizing: 12 Warning; 1 Severe Errors.
************* EnergyPlus Terminated--Fatal Error Detected. 13 Warning; 1 Severe Errors; Elapsed Time=00hr 00min 1.14sec

Return to “EnergyPlus General”

Who is online

Users browsing this forum: Majestic-12 [Bot], piterEt and 10 guests